Xerox WIDE FORMAT AccXES Firmware 10.0 b140 (Release Not Manual de usuario Pagina 1

XEROX WIDE FORMAT AccXES Firmware 10.0 b140 Release Notes

Page 10 5 New Features of 10.0 b 140 5.1 Support for 6030/6050 printer Via a new WebPMT page “Configure Remote Printer” the AccXES HFT controller ca

Page 11 6 New Features of 9.5 b 111 6.1 Single Page Job This feature, when enabled, will concatenate adjacent pages in a job that are the same width

Page 12 With 9.5 AccXES controller firmware and 3.2.5 Xerox Wide Format Scanner firmware or higher, it is now possible to move a feature key from one

Page 13 7 Release Notes The following information supplements the 10.0 customer user guides. 7.1 Controller 7.1.1 HFT and KLF Controller on the Xero

Page 14 7.2 Xerox Wide Format 721P Printer only 7.2.1 Job Cancel from the 721p Control Panel The current job can be cancelled using the 721 Control

Page 15 7.4.3 Upgrade Test Print After upgrading to the latest scanner firmware, check the Scanner Configuration section at the bottom of the Configu

Page 16 7.5.1 Manual feed media source will be ignored when used with the AccXES Client Tools’ page composition feature. Go to AccXES Client Tools &

Page 17 there can be scan errors; when there are fewer jobs in the queue, the jobs can then be resubmitted or scanned. Additionally, completed jobs w

Page 18 What to do: • Set Mismatch Mode to Substitute • Request a Media Size of ARCH E via WebPMT, ACT, or the Driver • Request a Media Size 36&

Page 19 7.6.12 Default PostScript Page Size If a PostScript job does not specify a page size (either by using a compatibility operator such as “lett

Page 2 Table of Contents 1 Introduction 4 1.1 FEATURE KEYS: 4 1.1.1 Feature Key Descriptions 4 2 Release Deliverables 6 2.1 Xerox 8825, 8830

Page 20 pattern is opened in Paint, any attempt to save the file will result in Paint crashing and no file saved. 7.6.16 Printer Password The printer

Page 21 8 Customer Issues Resolved 8.1 The following Customer issues were resolved in 10.0 b 140 Issue Description Problem Resolution Lines are mi

Page 22 9 Appendix 9.1 HFT Controller Installation for Xerox Wide Format Print System 8830 IMPORTANT NOTE: The controller will only accept the ins

Page 23 9.2.1 AccXES Client Tools Download the file named “HFT_8850_510dp_10_0b140.disk.bin”. A status sheet will be printed and indicate that the

Page 24 9.3.3 Unix Download the software using LPR with the following command line: lpr –P printername HFT_721p _10_0b140.disk.bin A status sheet w

Page 25 IMPORTANT NOTE: The 6030/6050 requires an 80 GB hard drive. The controller will only accept the installation when there are no active jobs b

Prepared by: Xerox Corporation 800 Phillips Road Building 139-64A Webster, New York 14580-9791 USA ©XEROX Inc. 2004. All rights res

Page 3 7.6.1 Printer Queue – Main WebPMT Screen 16 7.6.2 Backlit-Film media type 17 7.6.3 Netscape 6.1 users only 17 7.6.4 Netscape 7.0 users

Page 4 1 Introduction The AccXES Controller Firmware Release 10.0 b 140 provides multinational software for the Xerox Wide Format Print Systems 8825,

Page 5 • PostScript • Xerox Wide Format Scanner Features: Scan To Net (to create an electronic file from a scanned image) Scan to Print (to scan

Page 6 2 Release Deliverables 2.1 Xerox 8825, 8830 Print Systems The following executables are provided for the Xerox Wide Format Print System 8825,

Page 7 2.3 Xerox Print System 721p The following executables are provided for the Xerox Wide Format Print System 721p and support the Xerox Wide Form

Page 8 3 Recommended Configurations Table 1: Minimum (Min.) and Recommended (Rec.) RAM Configurations (MB) UP8 controller is no longer supported. N

Page 9 4 Release Installation NOTES: Feature keys from before version 9.0 B180 are no longer useable with version 10.0 firmware. New keys must be a