Xerox DocuTech 128 HighLight Color Guía de instalación Pagina 66
- Pagina / 86
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
4-38 DocuTech 128/155/180 HighLight Color Installation Planning Guide
Prepare for installation
Paper is fed into the printer with the long side as the leading edge.
When you purchase paper, buy long-grain paper. Make sure the
grain is parallel with the long side (long grain) for the most reliable
feeding and stacking.
Storing paper
Paper has a tendency to curl under the heat that is present inside
xerographic equipment. To minimize the amount of curling, use
paper with low moisture content. Paper with excessive moisture
content has a tendency to jam because of the greater curl. The
maximum recommended moisture content is 5.7 percent. Keep
these points in mind when preparing your paper storage area:
• Store paper in its own wrapper; do not leave it unwrapped or
where it can be damaged by dampness or heat.
• Store paper on a flat surface and not on its side or edge.
• Store reams of paper in a closed cabinet.
• Always store paper in a cool, dry area. Store on pallets or
shelves, not on the floor.
• Plan ahead and keep at least a day's supply of paper in the
same area as the printer to allow environmental stabilization
prior to printing.
Dry ink
Dry ink (also referred to as toner) is the black or color powder
which forms the image on the printed page. There are three
cartridges of dry ink in each carton. You should keep at least one
extra cartridge on hand at all times. The disposable cartridges are
easily changed with no mess.
The consumption rate of Xerox dry ink is dependent upon the area
coverage per page. Use only dry ink that is specified for use in the
DocuTech printer as described in the consumable supplies table.
Fuser oil
Fuser oil is a consumable item required by the printer. You should
keep at least one bottle on hand for installation by the service
representative. The consumption rate of Xerox fuser oil is
approximately one bottle per 200,000 pages.
Fuser oil is available as either Fuser Shield or Fuser Blend. Fuser
Shield is recommended for the printer in most cases. Fuser Blend
may be appropriate if you are performing post print inline finishing
operations. To be sure of which oil to use, contact your Xerox
representative.
NOTE: The label on the cap of the fuser bottle identifies the type
of fuser oil to use in the printer.
- Installation Planning 1
- Table of contents 3
- 5 Installation 4
- 6 Maintenance 4
- The regulation 6
- Check your understanding 7
- Additional queries 8
- Electrical safety 9
- Print Server 10
- Printer - ozone information 11
- Printer - laser safety 11
- Printer - operational safety 12
- For further information 13
- Safety notes 14
- 1 Introduction 15
- Requirements 16
- Industry Canada requirements 17
- Electromagnetic compatibility 17
- Environmental information 18
- European Union 19
- Other Countries 19
- Introduction 20
- 2 Planning responsibilities 21
- Customer responsibilities 22
- 3 Printer components and 25
- Inverter Feeder/Stacker (IFS) 26
- Feeder/Stacker 26
- Interposer 27
- Finisher 27
- 4 Prepare for installation 29
- Legend: 31
- Bypass transport dimensions 35
- Space planning guidelines 38
- HLC Printer 40
- HLC Production Publisher 43
- Mobility assist device 45
- Floor leveling 46
- Delivery access requirements 46
- Prepare for installation 47
- Passage A 48
- Power requirements 56
- Outlet configurations 56
- 60 Hz printer outlet voltages 57
- 50 Hz printer outlet voltages 57
- Electrical requirements 59
- Network requirements 62
- Environmental requirements 63
- Heat management 64
- Recommended weight and grade 65
- Storing paper 66
- Fuser oil 66
- Developer 67
- 4mm cartridge tape 67
- 5 Installation 69
- Software licensing 71
- Ongoing maintenance 71
- Installation 72
- 6 Maintenance 73
- Operator training 74
- Supplies service 74
- Routine maintenance 76
- Meter reading and reporting 76
- Consumable supplies table 76
- Transparencies 78
- Item Description 78
- U.S. part 78
- 604K24870 80
- 109R00314 81
- (Xerox Service 82
- Representative 82
- Maintenance 83
Relacionado con productos y manuales para Las Impresoras Láser / Led Xerox DocuTech 128 HighLight Color
(3 paginas)
(16 paginas)
(5 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales